Mgcamd 1.35 brak obrazu

Mgcamd 1.35 brak obrazu

Postnapisał misza1987 niedziela, 13 stycznia 2013, 14:25

Witam mam problem z ustawieniem mg camd normalnie pokazuje jak klucze lecą czas w milisekundach a obrazu brak. Ustawienia mg_cfg mam takie. Czy musze coś właczać żeby był obraz. Soft enigma enigma 2 2011-09-13 experimetal versia 3.1.0 2012-12-30

# EMM messages
# 00 don't show any EMMs (default)
# 01 show only valid EMMs
# 02 show valid and bad EMMs with complete data display
M: { 01 }

# ECM messages
# 00 don't show anything about ecm
# 01 normal mode, show pids processed, decoded ecm and cw
# 02 verbose mode, show valid and bad ECMs with data
C: { 01 }

# AU
# 00 disable, no emm pids processed
# 01 enable, emm pids always processed for soft-au and shared cards
# 02 auto, emm started only if channel cant be decoded
# 03 process emm pids for network cards update only
A: { 02 }

# key update (sum 01 or 02 with 04)
# 01 update only new keys, default setting
# 02 update all keys (used for valid PMK checking)
# 04 enable TPS au
# + tps SID, which pmt pid contains au pid
U: { 01 } 0x12c0

# config files folder (softcam, autoroll, ignore/priority)
# 00 files in /var/keys
# 01 files in /tmp
T: { 00 }

# network mode, use summ for several clients
# 00 no network (default)
# 01 newcamd netclient
# 02 radegast netclient
# 04 camd3 netclient
# 08 gbox netclient
# 32 cccamd netclient, card list saved as /tmp/cccamd.info
# (ECM only, supported server version up to 2.1.1, later not work)
G: { 01 }

# network retry, use summ for several options
# 00 disable
# 01 retry every new ecm
# 02 try to connect to offline shares every Q: seconds
# 04 try to detect and fast reconnect to lost (and not used atm) server
# + XX messages number and YY seconds to reconnect
# mg will reconnect to server, if no answer to last XX ecm/keepalive or
# if no answer for last ecm or keepalive sent for YY seconds
# set to 0 to disable
N: { 07 } 5 30

# network ecm timeout in seconds
K: { 05 }

# newcamd dead routes connect retry, sec
Q: { 600 }

# network shares priority
# 00 gbox, newcamd, cccamd, radegast, camd3 (default)
# 01 camd3, radegast, cccamd, gbox, newcamd
# 02 cccamd, newcamd, camd3, gbox, radegast
P: { 00 }

# on screen display type
# 00 No OSD (default)
# 01 neutrino
# 02 enigma
# 03 relook
# + user password for http auth
O: { 00 } username password

# on screen display Options, summ of:
# 01 show emu ecm
# 02 show network shares messages
# 04 show decoding failed / fta
# 08 show emm keys update
# + web port to use for osd
S: { 03 } 80

# Log option, summ of:
# 00 off
# 01 network udp log
# 02 log to console
# 04 file, appended ! delete it by yourself, before it eat all your hdd
# + IP udp-port log-file-name
L: { 02 } 172.16.1.1 28007 /tmp/mgcamd.log

# keep ecm cache, seconds
# every cache entry takes 28 bytes, so 24h cache will take *only* 240-400kb of memory,
# for openbox/elanvision users with remote shares make sense to set it higher than default value,
# to not hammer cards while timeshifting or playing crypted recordings.
E: { 15 }

# cache option, summ of:
# 00 Off (default)
# 01 Ecm pids cache, store pids used to decode in /tmp/ca_cache.list at exit, load at startup, same syntax as restore.list
# 02 Ecm data cache, remember CW for (E time
# 04 Emm cache for network cards, do not resend the same emm twice, cache not cleared until restart
H: { 07 }

# reread files, summ of:
# 00 No (default)
# 01 reread config file on channel change (including priority and ignore, but not replace/cache)
# 02 reread SoftCam.Key on channel change
# 04 reread SoftCam.Key if file changed
R: { 00 }

# debug, summ of
# 00 off (default)
# 01 debug ecm
# 02 debug emm
# 04 debug network ecm
# 08 debug network emm
# 16 debug network login
# 32 show mem/cpu stats every 1 min
# 64 add timestamp to log messages
D: { 00 }

# box type
# 00 autodetect, change only if you think wrong type detected.
# 01 dbox2
# 02 dreambox
# 03 triple-dragon
# 04 relook
# 05 openbox
# 06 dreambox/mips
# 08 stapi/kathrein
# 09 stapi/ipbox
# 11 stapi/openbox
B: { 01 }

# map all 180x nagra caids to 1801
# default is 01
F: { 01 }
misza1987
 
Posty: 3
Dołączył(a): niedziela, 13 stycznia 2013, 14:13
Dekoder:: SF1008GSE+

Re: Mgcamd 1.35 brak obrazu

Postnapisał niktwazny niedziela, 13 stycznia 2013, 14:26

A jak dasz tak B: { 11 } ?
Avatar użytkownika
niktwazny
Polish Koders Team
 
Posty: 433
Dołączył(a): środa, 8 czerwca 2011, 21:52
Dekoder:: SF1008GSE+

Re: Mgcamd 1.35 brak obrazu

Postnapisał krzysztof niedziela, 13 stycznia 2013, 16:29

Ja mam w tej pozycji :
B: { 00 }
krzysztof
 
Posty: 100
Dołączył(a): poniedziałek, 11 stycznia 2010, 20:54

Re: Mgcamd 1.35 brak obrazu

Postnapisał misza1987 niedziela, 13 stycznia 2013, 16:54

Próbowałem i w pozycjii B:{ 00} i {11} i dalej brak obrazu
misza1987
 
Posty: 3
Dołączył(a): niedziela, 13 stycznia 2013, 14:13
Dekoder:: SF1008GSE+

Re: Mgcamd 1.35 brak obrazu

Postnapisał ami68 niedziela, 13 stycznia 2013, 20:24

A: { 00 }
IPBox 910HD - E2 PKT HYPERION v4 + IPBox 200S x2 - ABEnigma
Avatar użytkownika
ami68
 
Posty: 280
Dołączył(a): niedziela, 23 maja 2010, 19:57
Dekoder:: CUBEREVO 910

Re: Mgcamd 1.35 brak obrazu

Postnapisał misza1987 wtorek, 15 stycznia 2013, 17:14

Udało się działa wszystko jest teraz ok po zmianie tego parametru A: {00} teraz całość w mg_cfg wygląda tak:

# EMM messages
# 00 don't show any EMMs (default)
# 01 show only valid EMMs
# 02 show valid and bad EMMs with complete data display
M: { 01 }

# ECM messages
# 00 don't show anything about ecm
# 01 normal mode, show pids processed, decoded ecm and cw
# 02 verbose mode, show valid and bad ECMs with data
C: { 01 }

# AU
# 00 disable, no emm pids processed
# 01 enable, emm pids always processed for soft-au and shared cards
# 02 auto, emm started only if channel cant be decoded
# 03 process emm pids for network cards update only
A: { 00 }

# key update (sum 01 or 02 with 04)
# 01 update only new keys, default setting
# 02 update all keys (used for valid PMK checking)
# 04 enable TPS au
U: { 01 } 0x12c0

# config files folder (softcam, autoroll, ignore/priority)
# 00 files in /var/keys
# 01 files in /tmp
T: { 00 }

# network mode, use summ for several clients
# 00 no network (default)
# 01 newcamd netclient
# 02 radegast netclient
# 04 camd3 netclient
# 08 gbox netclient
G: { 01 }

# network retry, use summ for several options
# 00 disable
# 01 retry every new ecm
# 02 try to connect to offline shares every Q: seconds
# 04 try to detect and fast reconnect to lost (and not used atm) server
# + XX messages number and YY seconds to reconnect
# mg will reconnect to server, if no answer to last XX ecm/keepalive or
# if no answer for last ecm or keepalive sent for YY seconds
# set to 0 to disable
N: { 07 } 5 30

# network ecm timeout in seconds
K: { 30 }

# newcamd dead routes connect retry, sec
Q: { 05 }

# network shares priority
# 00 gbox, newcamd, radegast, camd3 (default)
# 01 camd3, radegast, newcamd, gbox
# 02 newcamd, camd3, gbox, radegast
P: { 02 }

# on screen display type
# 00 No OSD (default)
# 01 neutrino
# 02 enigma
# 03 relook
# + user password for http auth
O: { 00 }

# on screen display Options, summ of:
# 01 show emu ecm
# 02 show network shares messages
# 04 show decoding failed / fta
# 08 show emm keys update
# + web port to use for osd
S: { 00 } 80

# Log option, summ of:
# 00 off
# 01 network udp log
# 02 log to console
# 04 file, appended ! delete it by yourself, before it eat all your hdd
# + IP udp-port log-file-name
L: { 02 } 172.16.1.1 28007 /tmp/mgcamd.log

# keep ecm cache, seconds
# every cache entry takes 28 bytes, so 24h cache will take *only* 240-400kb of memory,
# for openbox/elanvision users with remote shares make sense to set it higher than default value,
# to not hammer cards while timeshifting or playing crypted recordings.
E: { 15 }

# cache option, summ of:
# 00 Off (default)
# 01 Ecm pids cache, store pids used to decode in /tmp/ca_cache.list at exit, load at startup, same syntax as restore.list
# 02 Ecm data cache, remember CW for (E:) time
# 04 Emm cache for network cards, do not resend the same emm twice, cache not cleared until restart
H: { 07 }

# reread files, summ of:
# 00 No (default)
# 01 reread config file on channel change (including priority and ignore, but not replace/cache)
# 02 reread SoftCam.Key on channel change
# 04 reread SoftCam.Key if file changed
R: { 00 }

# debug, summ of
# 00 off (default)
# 01 debug ecm
# 02 debug emm
# 04 debug network ecm
# 08 debug network emm
# 16 debug network login
# 32 show mem/cpu stats every 1 min
# 64 add timestamp to log messages
D: { 00 }

# box type
# 00 autodetect, change only if you think wrong type detected.
# 01 dbox2
# 02 dreambox
# 03 triple-dragon
# 04 relook
# 05 openbox
B: { 11 }

# map all 180x nagra caids to 1801
# default is 01
F: { 01 }
misza1987
 
Posty: 3
Dołączył(a): niedziela, 13 stycznia 2013, 14:13
Dekoder:: SF1008GSE+

Re: Mgcamd 1.35 brak obrazu

Postnapisał wolku sobota, 29 czerwca 2013, 16:31

mgcamd dziala ci jako klient lokalny czy zdalnie czytasz z innego serwera ?
jesli zdalnie jak powinny wygladac pozostale pliki.
Czy serw stoi na newcamd ? Ja mam serwer na newcs (dm500) , klientem zdalnym jest nbox mgcamd 1.38. za chiny nie chce nic zaswiecic . Nie widze na newcs żeby w ogóle logował sie mój nbox do niego przy próbie odtworzenia zakodowanego kanału.
wolku
 
Posty: 3
Dołączył(a): niedziela, 16 czerwca 2013, 22:08
Dekoder:: SF1008SE+


Powrót do Cam-y | Moduły

Kto przegląda forum

Użytkownicy przeglądający ten dział: Brak zidentyfikowanych użytkowników i 7 gości